Polyacrylamide, a kind of flocculant, is called PAM for short. Main categories: anionic polyacrylamide (APAM), cationic polyacrylamide (CPAM), non-ionic polyacrylamide (NPAM).It is widely used in petroleum exploitation, water treatment, textile, printing and dyeing, paper making, mineral...
Polyacrylamide, a kind of flocculant, is called PAM for short. Main categories: anionic polyacrylamide (APAM), cationic polyacrylamide (CPAM), non-ionic polyacrylamide (NPAM).It is widely used in petroleum exploitation, water treatment, textile, printing and dyeing, paper making, mineral dressing, coal washing, medicine, sugar making, livestock breeding, building materials, agriculture and other industries.Be praised as "100 industry assistant", callled as "omnipotent product" also.
Selection and application of QUANSEN ACPAM
Amphoteric polyacrylamide is formed by the hydrolysis copolymerization of vinylides and vinyl cationic monomers.Transinfrared spectrum
According to the analysis, there are not only the carboxyl negative charge of acrylamide after hydrolysis, but also the vinyl positive charge.Therefore, an irregular polymer of amphoteric ions with both positive and negative charge is formed on the molecular chain.Zwitterionic is not a mixture of anionic and cationic.
1. After oil field test, the performance of this new type of zwitterion profile control agent is higher than that of other single ion characteristics.
2. The latest model of water treatment agent, on many occasions and sewage water, anionic polyacrylamide and cation polypropylene used alone than using an ionic polyacrylamide have very significant and synergies, PAM, to reduce the surface tension of friends can cation or anion is far greater than the same conditions exist alone, to reduce the surface tension of requirements, need to use both anionic and cationic polyacrylamide, if use undeserved, then both will produce white sediment, lose the use effect.PAM has the characteristics of amphoteric ions. It can complete the cooperation and synergism of anions and cations. There is no sediment production on the surface.
3. Sludge dehydrator, due to the nature of the urban sewage emissions is more and more complex, so the sewage treatment more and more high to the requirement of sludge dewatering agent, single some cationic polyacrylamide in sludge dewatering has some not too orientation, so my company for this kind of situation has developed the zwitterionic PAM sludge dehydrator, through a variety of sludge dehydration experiment was carried out and use, are better than a single ion characteristics of polyacrylamide.In particular, the use of amphoteric polyacrylamide in the sludge of oil refineries and chemical plants for pollution swelling and dehydration, its effect is more prominent.4) in the paper industry, as a chemical of paper making, the effect of PAM is even more unitary, especially in the aspect of retention and filtration, it can improve the water filtration rate under the network, reduce the loss of fiber filler, which has a good effect on the wet part system, and promotes and compensates the smoothness, strength and double-sided difference of paper forming.
4. Amphoteric polyacrylamide product form: the appearance of amphoteric polyacrylamide (ACPAM) is white powder.Cationic polyacrylamide is suitable for high speed centrifuge, belt filter press, plate and frame filter press and other special sludge dewatering machines.Therefore, high dehydration rate, low liquid content and low dosage of filter cake can greatly reduce the user's cost.It can also be used for the separation and purification of suspended turbidity substances in liquids such as hydrochloric acid and sulphuric acid.Therefore, this product is widely used in municipal sewage treatment plants, breweries, food plants, tanneries, paper plants, petrochemical plants, oil fields, metallurgy, chemical industry and cosmetics, and other sludge dewatering treatment.
Amphoteric polyacrylamide has better performance due to its containing cationic and anionic bases.Such flocculants can be used in a wide range of PH values, have higher water leaching capacity, lower cake moisture content, and can also be used in strong acid leaching ores or to recover valuable metals from acidic catalysts containing metals.Zwitterionic is not a mixture of anionic and cationic.If cationic polyacrylamide is used in conjunction with anionic polyacrylamide, the reaction will result in precipitation.Therefore, zwitterionic products are the most ideal.
【QUANSEN ACPAM Technical parameters】
【QUANSEN NPAM specifiction】
Dissolution duration （h)
The way the potion is added
The dosing should be done by gravity and pressure. No matter which dosing method is adopted, the dosing equipment should be set up from the solution pool to the solution pool and to the liquid liquid. The common liquid lifting equipment is metering pump and water ejector.
1. Gravity throw
Gravity is used to put the agent in the pump suction pipe or the suction hole of the water absorption well, and the pump impeller is used to mix.
2. Pressure drop
Use water pump or water ejector to put the agent into the original water pipe, which is suitable for the agent to be put into the pressure pipe, or need to be put into the water purification structure with higher elevation and distance.
3. Pump feeding
Pump feeding is to lift the liquid in the solution pool into the pressure pipe, which is enhanced by directly adopting metering pump and acid resistance.
Polyacrylamide before use generally need to be made into standby 0.1% ~ 0.5% of dilute solution, it is best not to store too long to make good solution, the concentration range of solution needs to be further diluted before use as 0.01 ~ 0.05 solution, the reason is that can be more ribs in the flocculating agent in the dispersion in the suspension system, can reduce the dosage, but also can obtain better flocculation effect.
1. For sludge dewatering, it is recommended to mix with a concentration of 0.2%, and the stirring time shall be put into use for 50 minutes.
2. During the experiment, 100ml of waste water was taken, and PAM solution was slowly dripping with syringe, about 0.5ml each time. The most suitable agent was determined according to the size of alum flowers, the density of flocs, the clarity of supernatant, the sedimentation rate and the dosage.
3. Applicable to pharmaceutical factory, leather factory, printing and dyeing sludge, chemical sludge, paper factory, sewage treatment plant, etc., with 10-20g of dry powder added to ton of wastewater.
【Using principle of QUANSEN ACPAM 】
The use of polyacrylamide should follow the following principles:
1. Powder polyacrylamide flocculant cannot be directly added to sewage.It must be dissolved in water before use, with its water solution to treat sewage.
2. The water of dissolved granular polymer should be clean (such as tap water), not sewage. Normal temperature water is ok, do not need to warm commonly.When the water temperature is less than 5 ℃ dissolve slowly.Over 40 ℃ temperature increase the dissolution rate is accelerated, but can make the polymer to speed up the degradation, affect the use effect.Ordinary tap water is suitable for the preparation of polymer solutions.Water with strong acid, strong alkali and high salinity is not suitable for preparation.
3. For the selection of polymer solution concentration, it is recommended to be 0.1% to 0.3%, that is, 1g to 3g polymer powder is added to 1 liter of water
【 attention 】
1. When used, it is extremely important to effectively disperse the product in the water, otherwise it will lead to the aggregation of dispersants and the production of "fisheye", and the dissolution time will increase.
2, use warm water can accelerate the dissolution rate, but the temperature is too high, lead to the thermal degradation of polymer chain, viscosity will be affected, the average water temperature should not exceed 50 ℃.
3. Using stirring can help dissolve, but stirring too violently can break down the long chain of dispersing agent, and it is better to adopt ship type propulsion.
4. The water solution should not be stored for more than 48 hours, otherwise the viscosity will be reduced and the effect will be affected.
【 safety 】
1. Quansen polyacrylamide is a water-soluble polymer, in case of water or liquids of high skid form is formed after soluble in water.Prevent products and their aqueous solutions from spilling onto the floor.If any, should timely use sand, sawdust adsorption, clean it.
2. The product is powder, the operation room should be careful to prevent dust inhalation or adhesion to the body.Wear masks, gloves and overalls to operate according to specifications.
3. Please refer to the safety data manual (MSDS) provided by the company for detailed safety operation guidance.
4. This product and its aqueous solution are not corrosive to the general materials such as stainless steel, plastic, rubber, glass and glass, etc., for the manufacture of tanks, mixers, gauges and pipelines.
1. High and stable product quality
2. Varieties of product series
3. Customer designed system solutions
4. Professional technical service team
5. Accumulated experiences of successful application at customer’s side
【 storage 】
The original product shall be kept sealed.Storage environments should be a cool, dry and ventilated, at room temperature for 10 ~ 40 ℃.Special precautions should be taken to prevent product absorption.
In accordance with the specified storage conditions, the original packaging products can be stable for at least 12 months.
【 packing 】
25kg composite paper bag /750kg pallet OR customer demand.