Livestock Wasterwater Polyacrylamide
Quansen polyacrylamide applies in livestock widely. Livestock wastewater mainly comes from animal feces, urine and flushing water.The main characteristics of aquaculture sewage are as follows: high concentration of organic matter, large suspended matter, deep color, and a large number of...
Quansen polyacrylamide applies in livestock widely. Livestock wastewater mainly comes from animal feces, urine and flushing water.The main characteristics of aquaculture sewage are as follows: high concentration of organic matter, large suspended matter, deep color, and a large number of bacteria, high content of ammonia nitrogen and organophosphorus, high content of COD up to 3000~12000mg/L, high content of ammonia nitrogen up to 800~2200mg/L, and excessive standard of SS dozens of times.It's biodegradable and has a bad smell.
Application of QUASEN PAM in Livestock
The pollution-free treatment of farm waste water can adopt different sewage treatment processes, and different equipment and polyacrylamide agents can be selected according to different processes to achieve the purpose of better effect and lower cost.
Root according to the different characteristics of sewage farms, processing equipment, processing technology and different processing requirements, using different types of QUANSEN PAM, professional flocculating agent to handle, the breeding of insoluble in water and soluble particles flocculation heavy fall out as much as possible, the maximum reduce processing difficulty of subsequent treatment process and water load, reached by black yellow water, water clear, breeding of flocculation of sewage sludge treated completely the first time.This specialized farms spring polyacrylamide flocculant, have very strong flocculation effect, but also to ensure that the mud sample floccules is enough big, good tolerance, there will be no use for a long time after drug flocculation and the problem of lower efficiency of pressure mud, solved the general flocculant dosage, insoluble particles flocculation is incomplete, black water problem, such as reduced pressure mud equipment requirements and into, is a kind of rare aquaculture wastewater flocculation treatment medicament.
【Selection of QUANSEN PAM】
By professional finalize the design experiments, using specific types of QUANSEN PAM, polyacrylamide, specifically for aquaculture wastewater, through simple flocculation sedimentation, can remove most of the organic waste in waste water breeding, greatly reduce the aquaculture wastewater COD and ammonia nitrogen, again through the subsequent biochemical treatment of anaerobic and exposed to oxygen, basically can reach discharge standard, and the water becomes clear, colorless, odorless, the main is to reduce the processing cost and processing time, it is a feasible aquaculture wastewater treatment ways.
The treatment agent of cationic polyacrylamide for QUANSEN factory is very effective. QUANSEN PAM Molecular weight is no other factory can match.
【Quansen PAM specification】
Dissolution duration （h)
1. High and stable product quality
2. Varieties of product series
3. Customer designed system solutions
4. Professional technical service team
5. Accumulated experiences of successful application at customer’s side
【 attention 】
1. When used, it is extremely important to effectively disperse the product in the water, otherwise it will lead to the aggregation of dispersants and the production of "fisheye", and the dissolution time will increase.
2, use warm water can accelerate the dissolution rate, but the temperature is too high, lead to the thermal degradation of polymer chain, viscosity will be affected, the average water temperature should not exceed 50 ℃.
3. Using stirring can help dissolve, but stirring too violently can break down the long chain of dispersing agent, and it is better to adopt ship type propulsion.
4. The water solution should not be stored for more than 48 hours, otherwise the viscosity will be reduced and the effect will be affected.
【 storage 】
The original product shall be kept sealed.Storage environments should be a cool, dry and ventilated, at room temperature for 10 ~ 40 ℃.Special precautions should be taken to prevent product absorption.
In accordance with the specified storage conditions, the original packaging products can be stable for at least 12 months.
【 packing 】
25kg composite paper bag /750kg pallet OR customer demand.